Metasurfaces provide applications for a variety of flat elements and devices due to the ability to modulate light with subwavelength structures. The working principle meanwhile gives rise to the crucial problem and challenge to protect the metasurface from dust or clean the unavoidable contaminants during daily usage. Here, taking advantage of the intelligent bioinspired surfaces which exhibit self-cleaning properties, a versatile dielectric metasurface benefiting from the obtained superhydrophilic or quasi-superhydrophobic states is shown. The design is realized by embedding the metasurface inside a large area of wettability supporting structures, which is highly efficient in fabrication, and achieves both optical and wettability functionality at the same time. The superhydrophilic state enables an enhanced optical response with water, while the quasi-superhydrophobic state imparts the fragile antennas an ability to self-clean dust contamination. Furthermore, the metasurface can be easily switched and repeated between these two wettability or functional states by appropriate treatments in a repeatable way, without degrading the optical performance. The proposed design strategy will bring new opportunities to smart metasurfaces with improved optical performance, versatility, and physical stability.

While plasmonic particles can provide optical resonances in a wide spectral range from the lower visible up to the near-infrared, often, symmetry effects are utilized to obtain particular optical responses. By breaking certain spatial symmetries, chiral structures arise and provide robust chiroptical responses to these plasmonic resonances. Here, we observe strong chiroptical responses in the linear and nonlinear optical regime for chiral L-handed helicoid-III nanoparticles and quantify them by means of an asymmetric factor, the so-called g-factor. We calculate the linear optical g-factors for two distinct chiroptical resonances to −0.12 and –0.43 and the nonlinear optical g-factors to −1.45 and −1.63. The results demonstrate that the chirality of the helicoid-III nanoparticles is strongly enhanced in the nonlinear regime.

Highly directive antennas with the ability of shaping radiation patterns in desired directions are essential for efficient on-chip optical communication with reduced cross talk. In this paper, we design and optimize three distinct broadband traveling-wave tantalum pentoxide antennas exhibiting highly directional characteristics. Our antennas contain a director and reflector deposited on a glass substrate, which are excited by a dipole emitter placed in the feed gap between the two elements. Full-wave simulations in conjunction with global optimization provide structures with an enhanced linear directivity as high as 119 radiating in the substrate. The high directivity is a result of the interplay between two dominant TE modes and the leaky modes present in the antenna director. Furthermore, these low-loss dielectric antennas exhibit a near-unity radiation efficiency at the operational wavelength of 780 nm and maintain a broad bandwidth. Our numerical results are in good agreement with experimental measurements from the optimized antennas fabricated using a two-step electron-beam lithography, revealing the highly directive nature of our structures. We envision that our antenna designs can be conveniently adapted to other dielectric materials and prove instrumental for inter-chip optical communications and other on-chip applications.

<jats:title>Abstract</jats:title><jats:p>Quantum well (QW) heterostructures have been extensively used for the realization of a wide range of optical and electronic devices. Exploiting their potential for further improvement and development requires a fundamental understanding of their electronic structure. So far, the most commonly used experimental techniques for this purpose have been all-optical spectroscopy methods that, however, are generally averaging in momentum space. Additional information can be gained by angle-resolved photoelectron spectroscopy (ARPES), which measures the electronic structure with momentum resolution. Here we report on the use of extremely low-energy ARPES (photon energy ~ 7 eV) to increase depth sensitivity and access buried QW states, located at 3 nm and 6 nm below the surface of cubic-GaN/AlN and GaAs/AlGaAs heterostructures, respectively. We find that the QW states in cubic-GaN/AlN can indeed be observed, but not their energy dispersion, because of the high surface roughness. The GaAs/AlGaAs QW states, on the other hand, are buried too deep to be detected by extremely low-energy ARPES. Since the sample surface is much flatter, the ARPES spectra of the GaAs/AlGaAs show distinct features in momentum space, which can be reconducted to the band structure of the topmost surface layer of the QW structure. Our results provide important information about the samples’ properties required to perform extremely low-energy ARPES experiments on electronic states buried in semiconductor heterostructures.</jats:p>

The nonlinear process of second harmonic generation (SHG) in monolayer (1L) transition metal dichalcogenides (TMD), like WS2, strongly depends on the polarization state of the excitation light. By combination of plasmonic nanostructures with 1L-WS2 by transferring it onto a plasmonic nanoantenna array, a hybrid metasurface is realized impacting the polarization dependency of its SHG. Here, we investigate how plasmonic dipole resonances affect the process of SHG in plasmonic–TMD hybrid metasurfaces by nonlinear spectroscopy. We show that the polarization dependency is affected by the lattice structure of plasmonic nanoantenna arrays as well as by the relative orientation between the 1L-WS2 and the individual plasmonic nanoantennas. In addition, such hybrid metasurfaces show SHG in polarization states, where SHG is usually forbidden for either 1L-WS2 or plasmonic nanoantennas. By comparing the SHG in these channels with the SHG generated by the hybrid metasurface components, we detect an enhancement of the SHG signal by a factor of more than 40. Meanwhile, an attenuation of the SHG signal in usually allowed polarization states is observed. Our study provides valuable insight into hybrid systems where symmetries strongly affect the SHG and enable tailored SHG in 1L-WS2 for future applications.

<jats:p>Secret sharing is a well-established cryptographic primitive for storing highly sensitive information like encryption keys for encoded data. It describes the problem of splitting a secret into different shares, without revealing any information to its shareholders. Here, we demonstrate an all-optical solution for secret sharing based on metasurface holography. In our concept, metasurface holograms are used as spatially separable shares that carry encrypted messages in the form of holographic images. Two of these shares can be recombined by bringing them close together. Light passing through this stack of metasurfaces accumulates the phase shift of both holograms and optically reconstructs the secret with high fidelity. In addition, the hologram generated by each single metasurface can uniquely identify its shareholder. Furthermore, we demonstrate that the inherent translational alignment sensitivity between two stacked metasurface holograms can be used for spatial multiplexing, which can be further extended to realize optical rulers.</jats:p>

GaAs-(111)-nanostructures exhibiting second harmonic generation are new building blocks in nonlinear optics. Such structures can be fabricated through epitaxial lift-off using selective etching of Al-containing layers and subsequent transfer to glass substrates. Herein, the selective etching of (111)B-oriented AlxGa1−xAs sacrificial layers (10–50 nm thick) with different aluminum concentrations (x = 0.5–1.0) in 10\% hydrofluoric acid is investigated and compared with standard (100)-oriented structures. The thinner the sacrificial layer and the lower the aluminum content, the lower the lateral etch rate. For both orientations, the lateral etch rates are in the same order of magnitude, but some quantitative differences exist. Furthermore, the epitaxial lift-off, the transfer, and the nanopatterning of thin (111)B-oriented GaAs membranes are demonstrated. Atomic force microscopy and high-resolution X-ray diffraction measurements reveal the high structural quality of the transferred GaAs-(111) films.

Topological states of light represent counterintuitive optical modes localized at boundaries of finite-size optical structures that originate from the properties of the bulk. Being defined by bulk properties, such boundary states are insensitive to certain types of perturbations, thus naturally enhancing robustness of photonic circuitries. Conventionally, the N-dimensional bulk modes correspond to (N – 1)-dimensional boundary states. The higher-order bulk-boundary correspondence relates N-dimensional bulk to boundary states with dimensionality reduced by more than 1. A special interest lies in miniaturization of such higher-order topological states to the nanoscale. Here, we realize nanoscale topological corner states in metasurfaces with C6-symmetric honeycomb lattices. We directly observe nanoscale topology-empowered edge and corner localizations of light and enhancement of light–matter interactions via a nonlinear imaging technique. Control of light at the nanoscale empowered by topology may facilitate miniaturization and on-chip integration of classical and quantum photonic devices.

We realize and investigate a nonlinear metasurface taking advantage of intersubband transitions in ultranarrow GaN/AlN multi-quantum well heterostructures. Owing to huge band offsets, the structures offer resonant transitions in the telecom window around 1.55 µm. These heterostructures are functionalized with an array of plasmonic antennas featuring cross-polarized resonances at these near-infrared wavelengths and their second harmonic. This kind of nonlinear metasurface allows for substantial second-harmonic generation at normal incidence which is completely absent for an antenna array without the multi-quantum well structure underneath. While the second harmonic is originally radiated only into the plane of the quantum wells, a proper geometrical arrangement of the plasmonic elements permits the redirection of the second-harmonic light to free-space radiation, which is emitted perpendicular to the surface.

We present a combined experimental and numerical study of the far-field emission properties of optical travelling wave antennas made from low-loss dielectric materials. The antennas considered here are composed of two simple building blocks, a director and a reflector, deposited on a glass substrate. Colloidal quantum dots placed in the feed gap between the two elements serve as internal light source. The emission profile of the antenna is mainly formed by the director while the reflector suppresses backward emission. Systematic studies of the director dimensions as well as variation of antenna material show that the effective refractive index of the director primarily governs the far-field emission pattern. Below cut off, i.e., if the director’s effective refractive index is smaller than the refractive index of the substrate, the main lobe results from leaky wave emission along the director. In contrast, if the director supports a guided mode, the emission predominately originates from the end facet of the director.

Optical metasurfaces are perfect candidates for the phase and amplitude modulation of light, featuring an excellent basis for holographic applications. In this work, we present a dual amplitude holographic scheme based on the photon sieve principle, which is then combined with a phase hologram by utilizing the Pancharatnam–Berry phase. We demonstrate that two types of apertures, rectangular and square shapes in a gold film filled with silicon nanoantennas are sufficient to create two amplitude holograms at two different wavelengths in the visible, multiplexed with an additional phase-only hologram. The nanoantennas are tailored to adjust the spectral transmittance of the apertures, enabling the wavelength sensitivity. The phase-only hologram is implemented by utilizing the anisotropic rectangular structure. Interestingly, such three holograms have quantitative mathematical correlations with each other. Thus, the flexibility of polarization and wavelength channels can be utilized with custom-tailored features to achieve such amplitude and phase holography simultaneously without sacrificing any space-bandwidth product. The present scheme has the potential to store different pieces of information which can be displayed separately by switching the wavelength or the polarization state of the reading light beam.

Topological photonic crystals (TPhCs) provide robust manipulation of light with built-in immunity to fabrication tolerances and disorder. Recently, it was shown that TPhCs based on weak topology with a dislocation inherit this robustness and further host topologically protected lower-dimensional localized modes. However, TPhCs with weak topology at optical frequencies have not been demonstrated so far. Here, we use scattering-type scanning near-field optical microscopy to verify mid-bandgap zero-dimensional light localization close to 100 THz in a TPhC with nontrivial Zak phase and an edge dislocation. We show that because of the weak topology, differently extended dislocation centers induce similarly strong light localization. The experimental results are supported by full-field simulations. Along with the underlying fundamental physics, our results lay a foundation for the application of TPhCs based on weak topology in active topological nanophotonics, and nonlinear and quantum optic integrated devices because of their strong and robust light localization.

<jats:p>Compact and robust cold atom sources are increasingly important for quantum research, especially for transferring cutting-edge quantum science into practical applications. In this study, we report on a novel scheme that uses a metasurface optical chip to replace the conventional bulky optical elements used to produce a cold atomic ensemble with a single incident laser beam, which is split by the metasurface into multiple beams of the desired polarization states. Atom numbers ~10<jats:sup>7</jats:sup> and temperatures (about 35 μK) of relevance to quantum sensing are achieved in a compact and robust fashion. Our work highlights the substantial progress toward fully integrated cold atom quantum devices by exploiting metasurface optical chips, which may have great potential in quantum sensing, quantum computing, and other areas.</jats:p>

<jats:p>The nonlinear processes of frequency conversion such as second harmonic generation (SHG) usually obey certain selection rules, resulting from the preservation of different kinds of physical quantities, e.g. the angular momentum. For the SHG created by a monolayer of transition-metal dichalcogenides (TMDCs) such as WS<jats:sub>2</jats:sub>, the valley-exciton locked selection rule predicts an SHG signal in the cross-polarization state. By combining plasmonic nanostructures with a monolayer of TMDC, a hybrid metasurface is realized, which affects this nonlinear process because of an additional polarization conversion process. Here, we observe that the plasmonic metasurface modifies the light-matter interaction with the TMDC, resulting in an SHG signal that is co-polarized with respect to the incident field, which is usually forbidden for the monolayers of TMDC. We fabricate such hybrid metasurfaces by placing plasmonic nanorods on top of a monolayer WS<jats:sub>2</jats:sub> and study the valley-exciton locked SHG emission from such system for different parameters, such as wavelength and polarization. Furthermore, we show the potential of the hybrid metasurface for tailoring nonlinear processes by adding additional phase information to the SHG signal using the Pancharatnam-Berry phase effect. This allows direct tailoring of the SHG emission to the far-field.</jats:p>

Nonlinear Pancharatnam–Berry phase metasurfaces facilitate the nontrivial phase modulation for frequency conversion processes by leveraging photon‐spin dependent nonlinear geometric‐phases. However, plasmonic metasurfaces show some severe limitation for nonlinear frequency conversion due to the intrinsic high ohmic loss and low damage threshold of plasmonic nanostructures. Here, the nonlinear geometric‐phases associated with the third‐harmonic generation process occurring in all‐dielectric metasurfaces is studied systematically, which are composed of silicon nanofins with different in‐plane rotational symmetries. It is found that the wave coupling among different field components of the resonant fundamental field gives rise to the appearance of different nonlinear geometric‐phases of the generated third‐harmonic signals. The experimental observations of the nonlinear beam steering and nonlinear holography realized in this work by all‐dielectric geometric‐phase metasurfaces are well explained with the developed theory. This work offers a new physical picture to understand the nonlinear optical process occurring at nanoscale dielectric resonators and will help in the design of nonlinear metasurfaces with tailored phase properties.

Free from phase-matching constraints, plasmonic metasurfaces have contributed significantly to the control of optical nonlinearity and enhancement of nonlinear generation efficiency by engineering subwavelength meta-atoms. However, high dissipative losses and inevitable thermal heating limit their applicability in nonlinear nanophotonics. All-dielectric metasurfaces, supporting both electric and magnetic Mie-type resonances in their nanostructures, have appeared as a promising alternative to nonlinear plasmonics. High-index dielectric nanostructures, allowing additional magnetic resonances, can induce magnetic nonlinear effects, which, along with electric nonlinearities, increase the nonlinear conversion efficiency. In addition, low dissipative losses and high damage thresholds provide an extra degree of freedom for operating at high pump intensities, resulting in a considerable enhancement of the nonlinear processes. We discuss the current state of the art in the intensely developing area of all-dielectric nonlinear nanostructures and metasurfaces, including the role of Mie modes, Fano resonances, and anapole moments for harmonic generation, wave mixing, and ultrafast optical switching. Furthermore, we review the recent progress in the nonlinear phase and wavefront control using all-dielectric metasurfaces. We discuss techniques to realize all-dielectric metasurfaces for multifunctional applications and generation of second-order nonlinear processes from complementary metal–oxide–semiconductor-compatible materials.

As flexible optical devices that can manipulate the phase and amplitude of light, metasurfaces would clearly benefit from directional optical properties. However, single layer metasurface systems consisting of two-dimensional nanoparticle arrays exhibit only a weak spatial asymmetry perpendicular to the surface and therefore have mostly symmetric transmission features. Here, we present a metasurface design principle for nonreciprocal polarization encryption of holographic images. Our approach is based on a two-layer plasmonic metasurface design that introduces a local asymmetry and generates a bidirectional functionality with full phase and amplitude control of the transmitted light. The encoded hologram is designed to appear in a particular linear cross-polarization channel, while it is disappearing in the reverse propagation direction. Hence, layered metasurface systems can feature asymmetric transmission with full phase and amplitude control and therefore expand the design freedom in nanoscale optical devices toward asymmetric information processing and security features for anticounterfeiting applications.

<jats:p>Surfaces covered with layers of ultrathin nanoantenna structures—so called metasurfaces have recently been proven capable of completely controlling phase of light. Metalenses have emerged from the advance in the development of metasurfaces providing a new basis for recasting traditional lenses into thin, planar optical components capable of focusing light. The lens made of arrays of plasmonic gold nanorods were fabricated on a glass substrate by using electron beam lithography. A 1064 nm laser was used to create a high intensity circularly polarized light focal spot through metalens of focal length 800 µm, N.A. = 0.6 fabricated based on Pancharatnam-Berry phase principle. We demonstrated that optical rotation of birefringent nematic liquid crystal droplets trapped in the laser beam was possible through this metalens. The rotation of birefringent droplets convinced that the optical trap possesses strong enough angular momentum of light from radiation of each nanostructure acting like a local half waveplate and introducing an orientation-dependent phase to light. Here, we show the success in creating a miniaturized and robust metalens based optical tweezers system capable of rotating liquid crystals droplets to imitate an optical motor for future lab-on-a-chip applications.</jats:p>