Nachrichten

Alexander Schlüter has been a new lecturer at the Faculty of Mechanical Engineering since January 2024. The newly established endowed professorship was created in collaboration with the Bette family business from Delbrück. Prof. Schlüter's Chair of Sustainable Industrialisation and Resilient Infrastructure conducts interdisciplinary research into the holistic approach to energy supply, production processes and products over their entire life…

Read more
Prof. Dr.-Ing. Peter Weidinger, Dr. M. Kröker und Prof. E. Moritzer stehen vor einem Roll-Up des WAK
Award ceremony for Dr. M. Kröker. The "Wissenschaftlicher Arbeitskreis Kunststofftechnik" (WAK) annually awards prizes for the best theses in the field of plastics technology.

Michael Kröker was awarded the Brose Prize by the "Wisssenschaftlicher Arbeitskreis Kunststofftechnik, WAK" (Scientific Working Group Plastics Technology) for his doctoral thesis on "Experimental and model-based investigations into the process behavior of semi-crystalline materials in the special injection molding process GITBlow", supervised by Univ.-Prof. Dr.-Ing. Moritzer. The Brose Prize is awarded for the development and research of new…

Read more

Once again, the Solid Freeform Fabrication Symposium was held in Austin, Texas, for its 34th edition, underscoring its importance as a renowned additive manufacturing conference in the United States. The DMRC contributed with all together 8 presentations on the following topics: Influence of Substrate Temperature on the Formation of Individual Weld Paths during Laser Cladding (LMD) when Processing 316L: Stefan Gnaase Assessing the Impact…

Read more
Photo (Paderborn University, Besim Mazhiqi): In the "NeMo.bil" project, so-called cabs are intended for last-mile transport.

The NeMo.bil (New Mobility) project consortium has reached an important milestone: The German Federal Ministry of Economics and Climate Protection is funding the NeMo.bil project to the tune of € 30 million. The aim of the project is to create an innovative, swarm-capable mobility system that will serve as a beacon for the whole of Germany and enable a new form of sustainable and demand-driven passenger and freight transport in rural areas. The…

Read more
Zwei Personen stehen vor einem Brandingdisplay der „International Conference on Composite Materials“ in Belfast
Die Mitarbeitenden des LiA Julian Lückenkötter und Shuang Wu (v.l.) auf der 23rd „International Conference on Composite Materials“ in Belfast.

The International Conference on Composite Materials (ICCM) is the leading international research conference on fibre-reinforced plastics and has been held every two years since 1975. The international conference brings together representatives from academia and industry to present the results of research and development projects. In addition to the optimisation of material and component properties, a particular focus is on the sustainability and…

Read more
Photo by Prof. Iryna Mozgova

A new chair enriches the ILH consortium. In August 2022, Prof. Dr. Iryna Mozgova succeeded Prof. Dr.-Ing. Rainer Koch as head of Data Management in Mechanical Engineering (DMB), which focuses on additive manufacturing and data analysis / public safety. The research areas include a number of important cross-cutting issues such as design, product development and quality management. Data management is a central and connecting topic that plays an…

Read more

The heart of the technical centre in the ILH research building at the Paderborn University is being installed! The 11 m high hydraulic double-column forming press, manufactured by Schuler Pressen GmbH, was delivered on 16 May and is now being installed in the centre of the experimental areas for materials technology, plastics technology and FRP processing. With a nominal force of 10,000 kN, it is the largest press available to the ILH. Funded by…

Read more

Am 21.02.2023 fand am Institut für Leichtbau mit Hybridsystemen (ILH) die erste Sitzung der Ende 2022 eingerichteten neuen Beiräte vom ILH und Paderborner Institut für Additive Fertigung (PIAF) statt.

Read more
[Translate to English:]
[Translate to English:]

In February, the research project "carboHEAT" funded by the German Federal Environmental Foundation (DBU) was successfully completed over the past 18 months in cooperation with the project partners of Hotset GmbH. In the future, heatable hybrid structures based on recycled carbon fibre fleeces (rCF) can be produced for a variety of further applications in addition to the project's focus on use as a heated floor panel in camping vehicles.…

Read more
Kick-off Meeting MADE-3D in the technical center of the lightweight building Y (Foto: Jennifer Bounoua)

6.7 million euros of funding – Paderborn University is leading a Europe-wide research project

Read more

Innerhalb von nur 10 Tagen ist es uns gemeinsam gelungen über 22.000 Euro für die Beschaffung eines Notstromaggregats zu sammeln. Es wurde bereits vor einigen Tagen bestellt und kann voraussichtlich die Reise noch Ende 2022 in die Ukraine antreten.

Read more

Bei dieser Gelegenheit gaben Prof. Dr.-Ing. Mirko Schaper und Prof. Dr. Thomas Tröster (ILH) Einblicke in moderne Fahrzeugtechnik und Verkehrskonzepte, Energieversorgung und Digitalisierung anhand der Initiative „Neue Mobilität Paderborn“.

Read more
Wissenschaftscafé Mobilität - Modell

Die Initiative „Neue Mobilität Paderborn“ (NeMo Paderborn) veranstalte anlässlich des Jubiläumsjahres der Universität Paderborn ein Wissenschaftscafé unter dem Titel „Mobilität im Dialog – Vernetzung von Land und Stadt“.

Read more
Foto (Universität Paderborn, Johanna Pietsch): Bei der Kick-Off-Veranstaltung im Y-Gebäude der Universität Paderborn haben die Konsortialpartner des Forschungsprojekts „Re²Pli“ Mitte August ihre Arbeit begonnen.

Fahrzeuge umweltfreundlicher und effizienter herstellen – das ist das Ziel eines neuen Forschungsprojekts unter der Leitung des Lehrstuhls für „Leichtbau im Automobil“ (LiA) an der Universität Paderborn.

Read more

With 524 oral and poster presentations, the Solid Freeform Fabrication (SFF) Symposium 2022 is again one of the key events for the AM comunity in the states. The DMRC contributed with all together 6 presentations on the following topics:

Read more

Contact

business-card image

Prof. Dr. Thomas Tröster

Key research area Sustainable Materials, Processes and Products

Chairman of the Institute for Lightweight Design with Hybrid Systems (ILH)

Write email +49 5251 60-5331
business-card image

Prof. Dr. Hans-Joachim Schmid

Key research area Sustainable Materials, Processes and Products

Chairman of the Paderborn Institute for Additive Fabrication (PIAF)

Write email +49 5251 60-2404
business-card image

Prof. Dr.-Ing. Eugeny Kenig

Key research area Sustainable Materials, Processes and Products

Chairman Competence Center for Sustainable Energy Technology (KET)

Write email +49 5251 60-2164

General information on the disciplines involved can be found on the corresponding websites:

Mechanical Engineering   Chemistry    Physics

 

Large-scale absorption-desorption plant at FVT

Outdoor PV laboratory at EET

Power Electronics Lab with emphasis on Wide-Bandgap applications at LEA

Being part of a network offers many advantages and opens up new perspectives. Technology transfer and industrial cooperation have a high priority at the University of Paderborn. In the ILH and the PIAF, there are long-standing contacts to companies of different sizes, regionally and nationwide.

ILH partners from research and industry

DMRC industry partners

KET industry partners